Contents

- 1 What are the steps to copy a line segment?
- 2 Which step in the construction of copying a line segment ensures that the new line segment has the same length as the original line segment Brainly?
- 3 What is the first step in constructing a line segment?
- 4 When copying segments and angles which step is the same?
- 5 What is the length segment AB?
- 6 How do you copy a segment by hand?
- 7 Which defines a line segment?
- 8 How you could use the construction tool or a compass and straightedge to create a line segment that is twice as long as?
- 9 How does this step ensure that the new angle will be congruent to the original angle?
- 10 What are the steps in bisecting a line segment?
- 11 What is the final step in bisecting a line segment?
- 12 Which is the first step in constructing an angle?
- 13 Can line segments be congruent?
- 14 What is the final step in copying an angle?
- 15 How do I make a copy of an angle?

## What are the steps to copy a line segment?

Copying a line segment

After doing this | |
---|---|

Step 1 |
Mark a point R that will be one endpoint of the new line segment. |

Step 2 |
Set the compasses’ point on the point P of the line segment to be copied. |

Step 3 |
Adjust the compasses’ width to the point Q. The compasses’ width is now equal to the length of the line segment PQ. |

## Which step in the construction of copying a line segment ensures that the new line segment has the same length as the original line segment Brainly?

**Step**-by-**step** explanation:

Using a compass **ensures that the new segment has the same length as the original** one. Taking a pivot point and then drawing a arc, this **distance** is the **copy**.

## What is the first step in constructing a line segment?

**Line Segment** Bisector, Right Angle

- Place the compass at one end of
**line segment**. - Adjust the compass to slightly longer than half the
**line segment**length. **Draw**arcs above and below the**line**.- Keeping the same compass width,
**draw**arcs from other end of**line**. - Place ruler where the arcs cross, and
**draw**the**line segment**.

## When copying segments and angles which step is the same?

⇒So, to bifurcate something that is **segments and angles**, you need either a line or line **segment**. ⇒So, the two **steps** which are **same** is, when bisecting **segments and angles** is, Option A→Draw a ray with one endpoint.

## What is the length segment AB?

The **length** of **segment AB** is 13 units.

## How do you copy a segment by hand?

**The correct procedure is:**

- Put the tip of the compass on the point A.
- Open the compass till the point B.
- Without changing the width of the compass, put the tip of the compass on point C.
- Draw an arc from C.
- Draw a line from C until a point in the arc.
- Mark and label the point of intersection as D.
- Done.

## Which defines a line segment?

The part of a **line** that connects two points. Adding the word “**segment**” is important, because a **line** normally extends in both directions without end. But a **line segment** has definite end points.

## How you could use the construction tool or a compass and straightedge to create a line segment that is twice as long as?

**Answer**

- Answer:
- 1.)
**Take**your**compass**and place**it’s**center on point A. - 2.) Set the
**compass**width to the length of AB. - 3.) Place the center of the
**compass**on B, and without adjusting the width of the**compass**, make an arc. - 4.)
- This new
**line segment**is now**twice as long as**AB. - Step-by-step explanation: Hope this helps:)

## How does this step ensure that the new angle will be congruent to the original angle?

**How does this step ensure that the new angle will be congruent to the original angle**? Because the distance is the same and the measure of the **angle will** be the same then the **next** model **will** have the same **angle** and it **will be congruent**.

## What are the steps in bisecting a line segment?

**STEP** 1: Draw a straight **line** with a ruler. **STEP** 2: Put the pin of a compass at the end of the **line** you want to **bisect**. Set the compass to more than half the length of the **line**, and draw an arc crossing the **line**. **STEP** 3: Keep the width of the compass the same, and from the opposite end of the **line** draw another arc.

## What is the final step in bisecting a line segment?

Obviously, the **final step** is drawing the **bisector**. That is what you do when you Mark the intersection points of the arcs, and draw a **line** through those two points.

## Which is the first step in constructing an angle?

Answer: Place the compass on the vertex of the **angle**, and draw an arc across both legs of the **angle**.

## Can line segments be congruent?

**Line segments** are **congruent** if they have the same length, or measure. All **line segments** have the same shape, so “size” is what we are really looking at when we want to know if two **line segments** are **congruent**.

## What is the final step in copying an angle?

Place the compass on the vertex of the new **angle**, and swing an arc similar to the first one you created. Draw a ray with one endpoint. This endpoint will be the vertex of the new **angle**.

## How do I make a copy of an angle?

**Refer to the figure as you work through these steps:**

- Draw a working line, l, with point B on it.
- Open your compass to any radius r, and construct arc (A, r) intersecting the two sides of
**angle**A at points S and T. - Construct arc (B, r) intersecting line l at some point V.
- Construct arc (S, ST).