- 1 Can I use new construction recessed lighting?
- 2 How much should it cost to have recessed lighting installed?
- 3 Should I use 4 inch or 6-inch recessed lights?
- 4 What is the difference between can lights and recessed lights?
- 5 How many can lights for a 12×12 room?
- 6 Do you need a permit to install recessed lighting?
- 7 Does recessed lighting add value to a house?
- 8 Can you daisy chain can lights?
- 9 Are recessed lights out of style?
- 10 What gauge wire for LED can lights?
- 11 Can LED recessed lights be covered with insulation?
Can I use new construction recessed lighting?
Remodel Fixtures vs.
If you can‘t get above the ceiling to run the wiring, you will probably have to use a remodel fixture. But if you have access to space above the ceiling where the fixture will be located, you can install new–construction recessed lights in your existing ceiling.
How much should it cost to have recessed lighting installed?
Recessed Lighting Installation Costs
The basic installation of recessed can lights runs from $200 to $250 per fixture for labor alone. For each fixture, the process takes about 2 1/2 hours at a $85 to $105 per hour labor rate. Both new construction and remodel projects take this long to install each one.
Should I use 4 inch or 6-inch recessed lights?
Choose one that will accommodate the height of your ceiling or the size of your wall. 4–inch and 5-inch fixtures are great in kitchens for providing overhead countertop lighting. 6–inch fixtures are most common for general lighting purposes. 7- to 9-inch fixtures will create a wider wash of light.
What is the difference between can lights and recessed lights?
Recessed lights, also known as can lights, are described as metal light housings installed in the ceiling for a sleek look that gives you back your ceiling. Their diameter generally varies from 3” to 6.”
How many can lights for a 12×12 room?
The typical rule-of-thumb is 24″ from each wall, and then 3-5 feet between cans. So in a 12′ room you’d probably want two rows of lights. Considering it is a bedroom and you don’t need it as bright as a kitchen, you can probably get away with 2 rows of 4 lights for a total of 8.
Do you need a permit to install recessed lighting?
You‘ll need an electrical permit if you are altering, changing, or adding to the electrical equipment for your home. If it involves the electrical wires of your home, you‘ll need a permit. If you‘re only swapping out a fixture, you don’t need one — but be careful!
Does recessed lighting add value to a house?
A bright way to increase the value of your home is to add lighting. Hire an electrician to add recessed lights to a dim kitchen or family room or elegant sconces to a formal dining or living room. You’ll enjoy the lighting now, and your home will feel more welcoming to home buyers later.
Can you daisy chain can lights?
Remember that you must run one ultra-thin extension cable (or run of low voltage wire) for each light. You can not daisy chain multiple lights together.
Are recessed lights out of style?
Recessed lighting will never go out of style. However, the finishes and sizes will vary and change as time goes by. There are too many advantages of having the lighting recessed for them to eventually go out of style or phase out.
What gauge wire for LED can lights?
Here’s some basic facts you should consider when installing recessed lights: Most lighting circuits in homes are either 15 or 20 amps. 15 amp circuits are the most common. 20 amp circuits require 12 gauge wire; 15 amps circuits allow for less expensive 14 gauge wire.
Can LED recessed lights be covered with insulation?
You could hire an electrician to replace each fixture with a sealed one rated for insulation contact (IC). Now it will be safe to heap insulation onto that spot. I do recommend that you replace your bulbs with LEDs because they’re so energy-efficient, but make sure they’re rated for use in fully enclosed fixtures.