Readers ask: What Is Flashing In Construction?

What is a wall flashing?

Flashings are water impervious membranes or metals installed in wall systems that collect water penetrating the exterior and facilitate directing the water back to the exterior. Wall flashings are often the most important component in a wall system.

What is flashing and why is it important?

Flashing secures joints in your roof and places that tend to receive a lot of water, like valleys between slopes. With adequate flashing, water is directed away from vulnerable areas of the roof and into gutters. Without flashing a roof would almost certainly develop leaks in sensitive areas.

What is the purpose of flashing on a house?

As all builders know, flashing is a thin sheet or strip of water-resistant material that’s installed at roof intersections and projections, around windows and doors, and along the tops of foundation walls to direct water flow away from the home. Flashing guides water out from the drainage plane to the exterior.

What materials are used for flashing?

What materials are used for flashing? Flashing can be made from many different materials, including metal (copper, aluminum, stainless steel, lead, etc.), plastic, or composite materials. The most durable (and, therefore, most expensive) flashing material is metal sheet flashing.

You might be interested:  FAQ: What Is Construction Paper Made Of?

Does flashing go over or under house wrap?

Be certain that the window flashing leads water over the house wrap(not behind it) at the ends of the window. The use of rigid plastic foam sheathing is also becoming more common in residential construction. If you tuck window flashing under the foam sheathing you may create a leak.

What is the most common material used for roof flashing?

Copper is the most preferred for most flashing applications. Aluminum – its durable and easy to form and relatively cheap. Aluminum is the best for a chimney, Valley or base flashing but a finish must be applied to prevent corrosion especially when it comes into direct contact with treated wood, concrete or cement.

What is window flashing?

Window flashing is a thin continuous piece of material that is installed to prevent water from getting into a structure from an angle or joint near windows. It is typically used on roofs, around windows and doors, and around any opening for pipes or electrical lines. Window flashing can be exposed or concealed.

How do you apply flashing to siding?

Cut a piece of flashing a minimum of four inches (102 mm) wide. Install the piece of lap siding, following one of the recommended nailing methods. Nail the siding, stopping before placing the final nail at the end. Slide half of the piece of pan flashing, oriented vertically, under the end of the siding.

What is the difference between flashing and counter flashing?

The base flashing (or apron flashing) is the bottom piece. Counterflashing: Placed opposite to base flashing, or above base flashing, counterflashing completes the two-part team. Step flashing: Step flashing is a rectangular piece of flashing bent 90 degrees in the center. It is used for roof to wall flashing.

You might be interested:  Quick Answer: Which Type Of Fall Is Responsible For The Highest Percentage Of Overall Deaths In Construction?

When should I use roof flashing?

Roof flashing is required on your roof to keep water from getting underneath your shingles, with the help of underlayment. Flashing is critical to certain areas of your roof — namely, the places where the roof surface meets a wall, valleys, protrusions such as vents and skylights, and the roof’s edges.

Why is it called flashing?

Etymology and related terms



The origin of the term flash and flashing are uncertain, but may come from the Middle English verb flasshen, ‘to sprinkle, splash’, related to flask. Strips of lead used for flashing an edge were sometimes called an apron, and the term is still used for the piece of flashing below a chimney.

What does flashing mean?

Flashing: “Flashing,” or exhibitionism is characterized by intense, sexually arousing fantasies, urges or behaviors involving exposure of the individual’s genitals to an unsuspecting stranger. The individual with this problem, sometimes called a “flasher,” feels a need to surprise, shock or impress his victims. 4 дня назад

How long should lead flashing last?

Simple. Lead expands a huge amount in the heat, shrinks a lot in the cold, and wanders about a bit at all temperatures in between. If this expansion and contraction are allowed to continue freely, the lead flashing will last for 100 years.

How do you use Aluminium flashing?

Begin to staple the edge of the sheet to the side of the roof. Aluminum is very soft, so take care not to press down too hard upon the metal, as this will dent and perhaps damage it. Continue to staple the flashing until it is securely in place, and tightly fitted against the side of the building and the roof.

Leave a Reply

Your email address will not be published. Required fields are marked *