When Passing A Construction Zone, You Should?

When you drive through a construction zone you should?

When traveling through a construction zone, drivers should be aware of some driving strategies that will ensure greater work zone safety.

  1. Slow down.
  2. Don’t tailgate.
  3. Stay a safe distance away from construction workers and their equipment.
  4. Watch for stopped traffic.
  5. Merge as soon as possible.
  6. Do not block traffic.

What are the first 3 things you should do when approaching a construction zone?

When you enter a construction zone or see that one is approaching, turn down (or turn off) your radio, end any cell phone calls, and keep both hands on the wheel and eyes on the road.

How should you approach a construction zone?

  1. Expect the unexpected in road construction zones.
  2. Slow down, be alert and pay attention to the signs.
  3. Comply with the directions given by the flagger.
  4. Be patient in road construction zones.
  5. Use the “Take 10” technique to change lanes.
  6. Slow down — don’t drive too fast for conditions.
You might be interested:  Question: How To Become A Female Construction Worker?

What should you not do when driving in a construction work zone?

DO NOT

  1. Speed up or slow down significantly while going through a work zone.
  2. Slow down to look at the construction work being done.
  3. Resume normal speed until after you emerge completely out of the work zone area.
  4. Tailgate. Most of the accidents within a work zone are rear-end collisions.
  5. Change lanes within a work zone.

How fast should you go in a construction zone?

The new rule goes for construction zones (but not necessarily maintenance projects, which tend to wrap up quickly) where the posted speed is already at least 35 mph. Drivers have to slow down by 10 mph or more in those zones if the project changes the roadway, like with concrete barriers or a narrower shoulder.

How slow are you supposed to go in a construction zone?

Construction Zone Speed Limit

Federal guidelines exist and the average speed in a work zone is between 45 mph and 55 mph. This is to give drivers and workers enough time to react to dangerous situations.

How long must you indicate before turning left or right?

Signal for at least 3 seconds before you make a manoeuvre. The last thing you should do before you turn right is check in your blind spot over your right shoulder in case another vehicle has not seen your indicator and has started to overtake you.

What is the primary cause of work zone crashes?

The root causes of work zone crashes are: Improper following distance. Distraction or inattention. Failure to use the “lean and look” method to eliminate the blind spot when making a lane change.

You might be interested:  FAQ: How To Make Under Construction Page Wordpress?

How many seconds should you signal before turning?

Signal for at least 100 feet before you turn left or right. Signal for at least 5 seconds before changing lanes on the freeway or highway.

Can you go to jail for speeding in a construction zone?

It is not a crime if a motorist speeds in a California construction zone. These violations are infractions under California law and an offender is not subject to incarceration.

Which S’s should you remember when driving through construction zones?

Being safe in a work zone means paying attention to the three S’s: speed, stress, and space.

What do you do if you drive through a work zone?

When possible, avoid work zones and use any detours that are available.

  1. Pay Attention. You should always keep your eyes on the road, but this is exceptionally important in work zones.
  2. Slow Down. Lane closures, traffic pattern shifts and reduced speeds are common in work zones.
  3. Move Into The Open Lane.
  4. Keep Your Distance.

Do work zone speed limits apply at night?

A: If the posted speed limit signs are visible and placed in a construction zone, that speed limit is the maximum speed allowed, no matter what time, day, date or if workers are present or not. Law enforcement actively enforces all speed limits, especially in a work zone.

What is the most common collision in a work zone?

Rear-end crashes (running into the rear of a slowing or stopping vehicle) are the most common type of work zone crash. Fatal work zone crashes occur most often in summer and fall.

You might be interested:  Quick Answer: How To Make A Sombrero Out Of Construction Paper?

What should you be alert for in a construction area?

Watch for brake lights, and be alert to the possibility that trucks and other vehicles might be pulling out of the work zone and onto the roadway. Obey the posted speed limit, and remember that fines are often doubled for traffic violations in a construction zone.

Leave a Reply

Your email address will not be published. Required fields are marked *