FAQ: How To Build A Swing Set Out Of Wood?

What is the best wood for a swing set?

Cedar and redwood are the most commonly selected wood for outdoor swing sets, and for good reason. These woods are known for being naturally resistant to disease, rot, and insect infestation. You will also find swing sets made of spruce, pine, or fir.

How much does it cost to build your own swing set?

The national average is between $500 and $5,000 to build a backyard playground, with most homeowners spending around $2,500 to build wooden playground with swings, a slide, and a climbing area with shade and mulch for the ground.



Cost to Build a Playground.

Build Playground Cost
Average Range $500-$5,000
Minimum Cost $375
Maximum Cost ​$10,000

Can you build your own swing set?

Swing sets are great projects for beginning DIY and mid-level DIYers. The place to start is with hardware kits that supply the fittings and fasteners, but not the lumber, or kits that supply finished lumber, fittings and fasteners. There are a few things you should know to build a safe set.

You might be interested:  Quick Answer: How To Build A Small Walking Bridge?

What do you put under a swing set?

What to Put Under Your Swing Set

  1. Wood playground mulch or engineered wood fiber (EWF)
  2. Rubber playground mulch.
  3. Pea gravel.
  4. Sand.

How far apart should Swings be on a swing set?

All swings should be at least two feet apart from each other. The distance between the main support frame and the swings should measure at least 30 inches to prevent entanglement and collision. Two feet should be between the swing set and the ground.

How long do wood swing sets last?

How Long Does a Wooden Swing Set Last? A swing set made of strong, durable wood should last 20 years or longer — some even last for generations. As with any material, the life expectancy of a wooden swing set depends on proper care and maintenance.

Is a 4×4 strong enough for a swing set?

Yes, a 4×4 that is 20′ long will work. A 4×4 that is 12′ long will support about 4,000 lbs. each (depending on the species and grade). A 16′ 4×4 will support about half that and a 20′ 4×4 will support almost 1,000 each, if its horizontally braced about half way up.

Are swing sets worth it?

If you have little kids, under 3, then a swing set in the back yard would be worth it. They will get enough years of use out of it to justify the cost and work. For older kids the park works just fine. They also have a swing set but the kids do so much more on the dome.

Is pressure treated wood safe for swing sets?

Pressuretreated lumber is an excellent choice for any outdoor playset, regardless of how concerned you are about safety. Just be sure to use highly corrosion-resistant fasteners. The new copper preserving compounds are very corrosive – more corrosive than the arsenic of years ago.

You might be interested:  How To Build A Bike Frame From Scratch?

What is the best swing set to buy?

  • BEST OVERALL: Gorilla Playsets Chateau Wooden Swing Set.
  • BEST BUDGET: Swing-N-Slide PB 8360 Ranger Wooden Swing Set.
  • BEST WOODEN SWING SET: Backyard Discovery Parkway Swing Set.
  • BEST FOR SMALL YARDS: Jump Power UFO Swing Set.
  • BEST FOR BABIES: Costzon Toddler Climber and Swing Set.

How high should swing set beam be?

For the swings, take the height of the swing beam and multiply times two. So, if the beam is eight feet high, you’ll need 16 feet of open space with protective surfacing in the front and back.

How do you anchor a swing set?

Step 1: Dig away the soil under two of the four corners, this will create a hole of about 55 cm deep and a diameter of about 40 cm. Step 2:Mount the anchors into the wood of the playset by first drilling the holes and secure them to the posts. Then fill the holes in the ground with concrete.

How do you build a bench swing?

  1. Step 1 – Make Swing Seat Support Boards.
  2. Step 2 – Cut Out Notches at the Bottom of Seat Supports.
  3. Step 3 – Insert and Attach 2×4 Boards into Seat Support Notches.
  4. Step 4 – Cut and Attach First 2 ½” Wide Seat Board.
  5. Step 5 – Finish Attaching the Remaining Seat Boards.
  6. Step 6 – Cut and Attach Armrest Support.

Leave a Reply

Your email address will not be published. Required fields are marked *