FAQ: How To Build Your Own Fireplace Mantel?

How do you build a fireplace mantel?

  1. lift old fireplace door unit out. Demolition.
  2. Mark for Mantel. Mantles are usually 60 inches off the floor.
  3. position mantel brace on line at center and attach. Attach Mantel Brace.
  4. cut a breastplate to fit around brace. Attach Breastplate.
  5. prev.
  6. Trim and Finish Mantel.
  7. new fireplace doors go in just like old doors.

How thick should a fireplace mantel be?

A depth of 7 inches is ideal for most mantels, as it allows plenty of room to accommodate decorative objects. Keep in mind that the top and the sides of the mantel should be the same depth.

What is the best wood to make a fireplace mantel?

Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.

You might be interested:  Question: How To Build Wood Patio Covers?

How much does it cost to build a fireplace mantel?

You’ll get the most design flexibility in a wood mantel that’s built to your specs—a job that costs anywhere from $2,000 to $5,000. There are specialty shops that do the work, or, if you’re undertaking a large renovation, your carpenter might be able to do the job.

How do you build a floating mantel on a brick fireplace?

How to Install a Mantel

  1. Remove the old mantel.
  2. Add support by drilling holes for lag shields, then install lag bolts into the brick.
  3. Measure carefully and drill corresponding holes for the wood mantel.
  4. Push the wooden mantel carefully into place using wood glue for extra support.

What is the average height of a fireplace mantel?

Again, “proper” height is relatively subjective to your fireplace, but average or standard fireplace mantel height construction is around 54” above the hearth’s floor. Your fireplace may fit this dimension or it might be on the shorter or taller end of the spectrum when it comes to mantel height above fireplace.

How far should a fireplace mantel stick out?

A mantel should extend a minimum of 3 inches beyond the firebox opening. If the fireplace has facing around the opening, the mantel can also extend 3 or more inches beyond that.

How do you hang a mantel on a rock fireplace?

How To Hang A Wood Mantel on a Stone Fireplace using Rebar {before & after}

  1. Drill a hole in the stone fireplace using a mason drill bit.
  2. Cut the rebar to size.
  3. Fill hole with Fuz It (liquid nail)
  4. Insert the rebar into the hole on the stone and hold in place to allow liquid nail to grab rod.
You might be interested:  Question: How To Build Outdoor Fire Pit With Bricks?

How high should a TV be above a mantle?

In general, the answer is 60-68 inches above the ground; however, this number will vary depending on the height of the homeowner. If you have to lift or strain your neck at all, it’s too high.

What is a pearl mantel?

Pearl Mantels is a leading manufacturer of affordable fireplace mantels, fireplace shelves, and decorative wall shelves. Your home will look more beautiful with a fireplace mantel or shelf from Pearl Mantels.

How do I replace my mantle?

Here’s how to replace your fireplace mantel in a few easy steps.

  1. Step 1 – Remove the Old Fireplace Mantel.
  2. Step 2 – Measure.
  3. Step 3 – Purchase a New Fireplace Mantel.
  4. Step 4 – Attach the Support Ledger.
  5. Step 5 – Prepare the New Mantel.
  6. Step 6 – Attach the Mantel to the Support Ledger Board.
  7. Step 7 – Secure the Mantel.

How much is a mantle?

Cost to Install a Fireplace Mantel

Fireplace Mantel Costs Zip Code Mantels
Basic Better
Fireplace Mantel – Material Prices $285.00 – $350.00 $555.00 – $825.00
Fireplace Mantel – Installation Cost $150.25$175.35 $190.50 – $220.05
Fireplace Mantel – Total $435.25$525.35 $745.50 – $1045.05

How do you attach a fireplace mantel to the wall?

Slide Over Bolts Method

  1. Locate the studs behind the brick, stone, or faux veneer.
  2. Drive 1/2in lag screws through each of the studs.
  3. Have a helper support the mantel while you mark the location of the support rods on the back of the beam.
  4. Apply construction adhesive into the holes.
  5. Slide into place, admire, and enjoy!

Leave a Reply

Your email address will not be published. Required fields are marked *