- 1 How do you build a recessed shelf?
- 2 How deep can recessed shelves be?
- 3 Can you hang a shelf on a stud wall?
- 4 How do you secure a built in shelf to the wall?
- 5 How do you make a recessed shelf in a bathroom?
- 6 HOW MUCH DO built-in shelves cost?
- 7 How do you fit alcove shelves?
- 8 How do you hang shelves on drywall?
- 9 How do you support a shelf without a stud?
- 10 Do shelves need to go into studs?
- 11 How much weight can a screw hold in a stud?
How do you build a recessed shelf?
How to do it
- Make an Inspection Hole. Locate studs with a stud finder.
- Cut Drywall. Measure how tall you’d like to make your shelf (we made ours 16 x 16 inches) and how high up you’d like it to be installed.
- Build Box Sides. Cut small sheet board and craft board to dimensions of interior shelf.
- Apply Putty.
- Insert Shelf.
How deep can recessed shelves be?
A recessed bookcase on a hall wall provides something of a challenge as a DIY project. Standard wall recesses only measure 3 ½ inches, the depth of the wall studs — not deep enough for even the smallest standard trade paperbacks, at 5 ½ inches wide.
Can you hang a shelf on a stud wall?
To put up a shelf on a plasterboard wall, you will need to find two studs (a stud is the upright wooden support in the wall to which the plasterboard is attached) to anchor your shelf brackets. Use your stud detector to find them, then draw two vertical guides along the lines of the studs.
How do you secure a built in shelf to the wall?
Attach the shelf to the wall by drilling pilot holes through the back corner and into wall studs, then toenailing the shelf to the wall with screws. Don’t drill through the inside of the bookshelf.
How do you make a recessed shelf in a bathroom?
Recessed shelves are ideal for creating extra storage in your bathroom.
Create a recessed shelf from a stud wall
- Make a hole. The first step to making a recessed shelf is to locate the studs within your chosen stud wall, using a stud finder.
- Measure and cut.
- Make a box shelf.
- Install the wall panels.
HOW MUCH DO built-in shelves cost?
The average cost for built-in bookshelves is between $1,500 to $4,000, with most homeowners paying around $3,000 for 5 linear feet of solid wood bookshelves, professionally installed.
Cost to Install Built-in Shelving.
|Built-in Shelving Costs|
|National average cost||$3,000|
How do you fit alcove shelves?
The easiest way to build this type of shelf is to fix three battens, one on each wall for the shelf to sit on. I always fit the back batten to the wall first, using a spirit level to make sure it is level. If the alcove is too narrow for your level, measure up from the floor or down from the ceiling instead.
How do you hang shelves on drywall?
Start by drilling a hole about the size of the tip of the threaded anchor. Then, take your power drill and drive the threaded anchor into the drywall just like you would with a normal screw. As with the expansion anchor, drive it in until it sits flush with the drywall.
How do you support a shelf without a stud?
Fortunately, there are several different options you can use to support a shelf. The most common one is a drywall anchor, which is like a plastic screw that plugs into drywall. If you’re working with plaster or need something that bears more weight, try using a molly bolt. For very heavy shelves, pick toggle bolts.
Do shelves need to go into studs?
Ideally, you should attach floating shelves (or anything else you’re hanging) to a wall stud, as this will give you the most supportive base for your project. A stud finder—a hand-held device that uses a magnet to detect metal, such as the nails and screws in the wall studs of your home—can help you locate these.
How much weight can a screw hold in a stud?
When hanging items on a stud, a screw in the stud can support between 80 and 100 lbs. An entire stud wall could support 20,000-30,000 lbs depending on its length.